Barrel/Hop-Up chamber upgrade on TM VSR-10

[Fallen]

Is the PSS10 Air Seal hop-up Chamber a good upgrade on air seal and/or accuracy?
http://shop.ehobbyasia.com/upgrade-p...10-series.html

It says that this chamber can fit AEG barrel and Laylax PSS10 barrel, but the AEG inner barrel and rifle barrel doesn't use the same size of bucking. So how it works? Because i already have PSS10 6.03 barrel installed on my VSR and i want to know if it will fit and be usefull.

Also, is a 6.01 inner barrel worth the price?

Thank you!

[Hectic]

i cant confirm the use of a barrel other then aeg bbecause i went with an aeg barrel howerver the chamber is good much beter then stock and alows beter hop adjustmnent id get harder rubber if you are running over 400 fps because even at 400 fps i use almost full hop on .28's as far as a 6.01 barrel, its a BA so jamming isnt much of an issue just use high end BB's like bastartds or i like KSC perfect .30's but whastever just use something good

[Fallen]

What AEG barrel you use? And what length? I tried to find AEG 430mm inner barrel 6.01, but i can't find one.

[H1TMAN]

According to Amos and ThunderCactus,

The PSS10 6.03 barrel is the best bang for buck barrel for the VSR10 and they both recommand sticking with mauri hop up assembly. If you look at most of their posts on VSR upgrades they state that the 6.01 barrel is for higher velocity and that for best accuracy is the 6.05 barrel. I've also seen the same comments on Arnies and Airsoft Retreat.

[Hectic]

I ordered a custom one edgi I think and it is 510mm I think due to my base being a Ted sd 700 that has an outer longer then any other vsr clone

[ThunderCactus]

I use 430mm laylax 6.03 and just the stock marui chamber, my rifle is extremely consistent

[Fallen]

Ok

What is the best hop-up bucking for a rifle with a 6.03 laylax inner and around 470-500 FPS. I installed a Nine-Ball pistol bucking because the stock one was destroyed, but i don't know if this is the best one.
http://www.wgcshop.com/wgc2008/main/...tid=62&cat=266

Also, i need a new spacer for my hop-up unit because the old one is compressed and doesn't work well, but i can't find one to replace it.

[ThunderCactus]

firefly hard would be best
But why run your rifle so hard?
My typical engagement distance is 100-150ft, I run 430fps, and my rifle is accurate out to 200 feet. Accurate to 150ft in 26km/h crosswind too

I've found my rifle is significantly more accurate at 430 than it was at 470.

[Fallen]

Originally Posted by ThunderCactus

But why run your rifle so hard?
My typical engagement distance is 100-150ft, I run 430fps, and my rifle is accurate out to 200 feet. Accurate to 150ft in 26km/h crosswind too

I've found my rifle is significantly more accurate at 430 than it was at 470.

When i bought my VSR, i had around 500 FPS, so I upgraded the spring for one that is soppused to shot around 500 FPS, but all my internal was stock with a lot of air leak. With a 500 fps spring, i was at 350-370FPS. But when i upgraded my internal, i don't cahnge the spring, so now im at +/- 470 FPS. But my bolt is very hard to pull, so i will probably change the spring.

[Hectic]

I have a question, the PSS10 springs does the tightly coiled end go on the spring guide or in the piston?