KA M4 Barrel Nut Help

Eeyore · March 29th, 2012, 20:02

I'm trying to remove the barrel nut off of a KA M4. The thing won't budge, I'm using an armorers wrench and still nothing. Anyone else have this issue? Is the thing glued on or something.

HKGhost · March 29th, 2012, 20:07

Add some oil into the threads and pop it into the freezer over night. Or for a few hours if you're in a rush. If that still won't work. Use a heat gun and heat it for a few minutes and try again. Only heat the barrel nut.

Amos · March 29th, 2012, 20:07

Talk a soldering iron, crank it to full and hold it on the barrel nut for a good while and get it nice and hot.. IIRC, there's locktite involved on KA nuts

Or a propane torch.. but take out your inner barrel + hop, all plastic pieces in the upper receiver and any small metal springs

Ghostnote · March 29th, 2012, 20:22

On mine (and one other one I saw), there are shims between the receiver and barrel nut and they got twisted up into the threads of the barrel nut. This may be the case. I ended up dremmeling off the delta ring.

As far as I know, king arms does not put loctite on their nuts. I have only taken apart 4 of them though. Its probably better to try the heating/cooling suggestions first.

SultanOfShwing · March 29th, 2012, 20:43

For me it took securing the upper using the barrel in a vice. Then 1 person holding the barrel steady while another person torqued the nut using pliers and two hands. Barrel got a little mangled during the operation

Carlito564 · March 30th, 2012, 00:01

I broke my receiver trying to take the damn thing off. I even used a vice and a pipe wrench but still it didn't budge until my receiver snapped.

Kozzie · March 30th, 2012, 14:04

Are these things CW threaded or CCW.

m102404 · March 30th, 2012, 14:47

All delta rings are "normal"...righty tighty/lefty loosey.

XZIVR · March 30th, 2012, 18:02

On my KA there was no loctite or anything, it was just very effing tight. Used the proper AR tool with the upper clamped in a vice, and it started to twist the upper before the nut would budge. I hit it with the heat gun on full blast, didn't help. Pounded on the wrench.. nothing. In the end I had to cut the damn thing off. Luckily AirsoftParts carries replacements.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

March 29th, 2012, 20:07	#2
HKGhost Trader rating Join Date: Nov 2009 Location: Mississauga, ON	Add some oil into the threads and pop it into the freezer over night. Or for a few hours if you're in a rush. If that still won't work. Use a heat gun and heat it for a few minutes and try again. Only heat the barrel nut. __________________ Please email me as I'm not on ASC too often. Custom Build \| Upgrades \| Repairs \| Maintenance Contact: ghostgunwork@gmail.com / Private Message

March 29th, 2012, 20:07	#3
Amos Trader rating Join Date: Aug 2006 Location: Tokushima, Japan	Talk a soldering iron, crank it to full and hold it on the barrel nut for a good while and get it nice and hot.. IIRC, there's locktite involved on KA nuts Or a propane torch.. but take out your inner barrel + hop, all plastic pieces in the upper receiver and any small metal springs __________________ Custom Builds: FA3674U Krinkov G3SD6

March 29th, 2012, 20:43	#5
SultanOfShwing Trader rating Join Date: Jan 2009 Location: Surrey, BC	For me it took securing the upper using the barrel in a vice. Then 1 person holding the barrel steady while another person torqued the nut using pliers and two hands. Barrel got a little mangled during the operation __________________

March 29th, 2012, 20:22	#4
Ghostnote Trader rating Join Date: Feb 2010 Location: Markham	On mine (and one other one I saw), there are shims between the receiver and barrel nut and they got twisted up into the threads of the barrel nut. This may be the case. I ended up dremmeling off the delta ring. As far as I know, king arms does not put loctite on their nuts. I have only taken apart 4 of them though. Its probably better to try the heating/cooling suggestions first.

March 30th, 2012, 00:01	#6
Carlito564 Trader rating Join Date: Sep 2010 Location: Sudbury, Ontario	I broke my receiver trying to take the damn thing off. I even used a vice and a pipe wrench but still it didn't budge until my receiver snapped. __________________ Molon Labe

March 30th, 2012, 14:04	#7
Kozzie a.k.a. Greedy Trader rating Join Date: Dec 2010 Location: Toronto	Are these things CW threaded or CCW.

March 30th, 2012, 14:47	#8
m102404 Tys Trader rating Join Date: Apr 2006 Location: Toronto	All delta rings are "normal"...righty tighty/lefty loosey.

March 30th, 2012, 18:02	#9
XZIVR Trader rating Join Date: Mar 2011 Location: Calgary, AB	On my KA there was no loctite or anything, it was just very effing tight. Used the proper AR tool with the upper clamped in a vice, and it started to twist the upper before the nut would budge. I hit it with the heat gun on full blast, didn't help. Pounded on the wrench.. nothing. In the end I had to cut the damn thing off. Luckily AirsoftParts carries replacements.

KA M4 Barrel Nut Help

Doctor's Corner