Airsoft Canada
https://blackblitzairsoft.myshopify.com/

Go Back   Airsoft Canada > Discussion > Airsoft Guns Discussion
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

Anyone have any problems with the KWA MP9?

:

Airsoft Guns Discussion

Reply
 
Thread Tools
Old September 14th, 2019, 17:24   #1
jwm470
 
Join Date: Feb 2019
Location: Waterloo, Ontario
Anyone have any problems with the KWA MP9?

So I've had my mp9 for a while now, but for some reason it's started to act up and jam on me. It almost looks like the bolt doesn't fully cycle back and will leave a gap. Although the cylinder looks like its resetted its just the bolt thats not cycled. ANyone got any advice?
jwm470 is offline   Reply With Quote
Old September 14th, 2019, 19:35   #2
Drakker
Official ASC Geomorphologist
 
Drakker's Avatar
 
Join Date: Sep 2009
Location: Montr?al south shore, Qc
This usually happens when a BB gets inside the gun and blocks the movement of the loading nozzle. It's unfortunately a common problem with this gun.
__________________
Keep quiet. Sound travels faster than BBs.

Québec province's master age verification representative.
Drakker is offline   Reply With Quote
Old September 14th, 2019, 21:09   #3
jwm470
 
Join Date: Feb 2019
Location: Waterloo, Ontario
damn, that's crappy. Any way to remedy it? whenever i looked to see and pulled back the bolt there was no BB in the chamber though.
jwm470 is offline   Reply With Quote
Old September 15th, 2019, 14:07   #4
Drakker
Official ASC Geomorphologist
 
Drakker's Avatar
 
Join Date: Sep 2009
Location: Montr?al south shore, Qc
Remove the upper, and see if a BB or something else falls out.
__________________
Keep quiet. Sound travels faster than BBs.

Québec province's master age verification representative.
Drakker is offline   Reply With Quote
Old September 15th, 2019, 14:55   #5
jwm470
 
Join Date: Feb 2019
Location: Waterloo, Ontario
I tried that and nothing came out. I also tried making the disconnector spring looser which did help close the gap a bit but it still has problems. Maybe the actual recoil spring isn't strong enough?
jwm470 is offline   Reply With Quote
Old September 15th, 2019, 15:04   #6
Ratters
 
Ratters's Avatar
 
Join Date: Jul 2003
Location: Vancouver
mp9

There are two long but smaller diameter springs that run along the inside edge of the nozzle to the body (I can't remember their function) but they do at times get completely destroyed and this could be the cause of your problem
__________________
Can´t sleep. Clowns will eat me!
Ratters is offline   Reply With Quote
Old September 15th, 2019, 15:07   #7
Ratters
 
Ratters's Avatar
 
Join Date: Jul 2003
Location: Vancouver
mp9

There are two long but smaller diameter springs that run along the inside edge of the nozzle to the body (I can't remember their function) but they do at times get completely destroyed and this could be the cause of your problem.

Look at the manual and the exploded parts diagram. This will give you a better understanding of what could be going wrong.
__________________
Can´t sleep. Clowns will eat me!
Ratters is offline   Reply With Quote
Old September 16th, 2019, 14:05   #8
Skeletor
 
Skeletor's Avatar
 
Join Date: Jun 2003
Location: Guelph, Ontario
Bring it into Blackblitz and we can take a quick look at it. Could be something simple, could need to be submitted for tech work.
Skeletor is offline   Reply With Quote
Old December 23rd, 2019, 14:07   #9
jwm470
 
Join Date: Feb 2019
Location: Waterloo, Ontario
Quote:
Originally Posted by Skeletor View Post
Bring it into Blackblitz and we can take a quick look at it. Could be something simple, could need to be submitted for tech work.
I just got it back from Blitz, they said that they couldn't figure it out. I'm thinking of ordering a new bolt assembly like the low powered one and see if that might help.
jwm470 is offline   Reply With Quote
Old December 23rd, 2019, 15:11   #10
wildcard
 
wildcard's Avatar
 
Join Date: Dec 2001
Location: In my man cave
Send a message via MSN to wildcard Send a message via Yahoo to wildcard
Quote:
Originally Posted by jwm470 View Post
So I've had my mp9 for a while now, but for some reason it's started to act up and jam on me. It almost looks like the bolt doesn't fully cycle back and will leave a gap. Although the cylinder looks like its resetted its just the bolt thats not cycled. ANyone got any advice?
Check the nozzle spring, from what you described it looks like nozzle spring are either worn out or they snapped off
wildcard is offline   Reply With Quote
Old December 26th, 2019, 13:29   #11
Kos-Mos
 
Kos-Mos's Avatar
 
Join Date: Nov 2005
Location: Lévis (QC)
There is a short but heavy spring that pulls the bolt back.
It's known to be too heavy and prevent the bolt from fully closing up.

Get it to jam, remove the upper receiver (plastic) then nudge the bolt forward a bit. If it fires, it's that spring.
Cheap fix is to jam a flat screw driver in the spring and twist to stretch it a bit.

If I remember correctly it's part number 162 on the exploded diagram. It's the sear disconnector spring.
__________________
Quote:
Originally Posted by Drake View Post
Damnit, don't make me add "no discussing temporal paradoxes" to the rules or I'll go back in time and ban you last week.
Kos-Mos is offline   Reply With Quote
Old January 6th, 2020, 13:18   #12
jwm470
 
Join Date: Feb 2019
Location: Waterloo, Ontario
Quote:
Originally Posted by Kos-Mos View Post
There is a short but heavy spring that pulls the bolt back.
It's known to be too heavy and prevent the bolt from fully closing up.

Get it to jam, remove the upper receiver (plastic) then nudge the bolt forward a bit. If it fires, it's that spring.
Cheap fix is to jam a flat screw driver in the spring and twist to stretch it a bit.

If I remember correctly it's part number 162 on the exploded diagram. It's the sear disconnector spring.
I think that I've tried this is the spring is the one that I'm thinking of, i found that it did in fact help a bit and close the gap but the gun would still have one and wouldn't fully cycle again.
jwm470 is offline   Reply With Quote
Old January 8th, 2020, 12:39   #13
jwm470
 
Join Date: Feb 2019
Location: Waterloo, Ontario
Quote:
Originally Posted by wildcard View Post
Check the nozzle spring, from what you described it looks like nozzle spring are either worn out or they snapped off
I also think that this is the problem, but I just cant seem to get the little pins out at the rear of the bolt assembly to get access to the springs they are too tight for me to get out.
jwm470 is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Discussion > Airsoft Guns Discussion

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada
https://blackblitzairsoft.myshopify.com/

All times are GMT -4. The time now is 19:03.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.