Airsoft Canada
http://triggerairsoft.com/shop/

Go Back   Airsoft Canada > Discussion > Doctor's Corner > Gas Gun Solutions
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

Revolver Cycling problem ? look at the cylinder lock.

:

Gas Gun Solutions

Reply
 
Thread Tools
Old September 26th, 2008, 19:02   #1
Jimski
 
Jimski's Avatar
 
Join Date: Jun 2005
Location: Montreal
Revolver Cycling problem ? look at the cylinder lock.

Hello

this is a solution.

Tonight I broke my M500, but this made me learn something:

The cylinder lock (this is the part that protrudes out of the frame at the bottom of the cylinder) makes sure that there is coaxiality (alignement?) between the cylinder and the barrel.
Most of the cycling problem come from something wrong at the cylinder lock level.

My old 357 TM had this problem, and I remember the cylinder lock was wobbly.
Tonight the lock on my 500 broke (tanks to Tanaka's CHEAP CRAP POT METAL ), and the exact same problem I had on the 357 started appearing.

So next time your revolver behaves weird, look at the lock.

good night everybody!

jim
__________________

Last edited by Jimski; September 28th, 2008 at 11:03..
Jimski is offline   Reply With Quote
Old September 26th, 2008, 19:37   #2
Mantelope
Scotty aka harleyb
 
Mantelope's Avatar
 
Join Date: Mar 2004
Location: Toronto, Ontario
Send a message via AIM to Mantelope Send a message via MSN to Mantelope
Gotta have your thread moved into solutions. Which I've done. Cheers!
__________________
Mantelope is offline   Reply With Quote
Old September 26th, 2008, 19:53   #3
Murdoch
 
Murdoch's Avatar
 
Join Date: May 2006
Location: Scarborough, Ont.
Send a message via MSN to Murdoch
That lever which locks the cylinder in place is the most poorly designed piece of shite I've seen. Like you said, it's a piece of pot metal with a piece of what should-be spring steel press fit to it. Every time you cock the hammer, it puts pressure on the steel piece and in turn on to the press fitting. It's almost designed to destroy itself eventually. I've tried to cut my own piece out of a square bit of metal, but it's just so damn small and oddly shaped.

I love my Tanaka revolvers but that part alone keeps me from using them more often. Boo-urns Boo-urns...

M


EDIT: Here's the closest I've come to finding a new one: http://www.uncompany.com/pageproduct...sp?prodid=9927

Last edited by Murdoch; September 27th, 2008 at 19:41..
Murdoch is offline   Reply With Quote
Old September 26th, 2008, 20:22   #4
Jimski
 
Jimski's Avatar
 
Join Date: Jun 2005
Location: Montreal
thx Mantelope
thank you Murdoch for the input

Victims! here are the symptoms I got:

-goes 'Pooof' sometimes and no BB comes out.
-rubber O-rings in the cylinder start getting blasted and deformed
-cylinder sometimes locks in position, double action fails.
-cylinder lock doesn't lock hard enough

anyone knows what Tanaka's homepage is?
__________________
Jimski is offline   Reply With Quote
Old February 21st, 2009, 15:32   #5
Jimski
 
Jimski's Avatar
 
Join Date: Jun 2005
Location: Montreal
Question About to take apart a Tanaka M500 S&W - any advice?

Hello all

I'm about to take apart my M500 to fix the cylinder lock that broke.
I will take the part out and pin ( or double-pin) a piece of metal made to act like the original thing ( I lost it).

Is there anything I should know when taking apart the gun?

thanks you very moch.
__________________
Jimski is offline   Reply With Quote
Old February 22nd, 2009, 11:51   #6
Jimski
 
Jimski's Avatar
 
Join Date: Jun 2005
Location: Montreal
waow the M500 crowd is amazing

anyway here are some pics, for your enjoyment.

I discovered 5mn too late by looking on the manual that the upper right screw on the body is FAKE.
do not attempt to unscrew it...
I will probably be sticking a fake screw head in this position to replace the one I drilled away thinking it was locked

M500 opened showing internals:
very clean like a bmw


The Cylinder Lock I had to fix (blurry), and the wall hook I used to fix it


a better view of the fixed part, not soldered yet


the part in position


I have no idea if it's going to work.
The width and depth of the hook seem alright, I'll be adjusting the elevation today, and soldering before I can test.
The big deal is that the cylinder has to be perfectly aligned with the barrel...

in position


it ended up being too high. modifying...
here it was soldered but I switched to PC7.
__________________

Last edited by Jimski; February 22nd, 2009 at 16:35..
Jimski is offline   Reply With Quote
Old February 23rd, 2009, 08:15   #7
Jimski
 
Jimski's Avatar
 
Join Date: Jun 2005
Location: Montreal
heya all.

PC7 didn't cure properly for some reason ( or I didn't wait long enough ) and the part broke again.
I ended up using polyurethane glue, this thing is stronger than it looks and fills all the space you can't get with soldering or putty.

The part actually works, its elevation needs to be very precisely adjusted to release the cylinder and block it right afterwards.This part suffers a very pic torsion to the left, I suspect it's going to break again. As murdock said it would need to be made of steel.

The good news is that it apparently restored a proper cycling, the barrel coaxiality seeming not so hard to obtain after all (all the gas comes out front)
coming next:shooting test
__________________

Last edited by Jimski; February 23rd, 2009 at 08:18..
Jimski is offline   Reply With Quote
Old February 24th, 2009, 07:48   #8
Jimski
 
Jimski's Avatar
 
Join Date: Jun 2005
Location: Montreal
it's working!

Polyurethane glue is super strong.

When gluing the pieces it's a good idea to put a drop of glue on a surface near the pieces: this way you can see how it cures and expanses, and you can wait for it to be truly hard before trying the part.(takes more than 24 hours)

Apparently barrel coaxiality in not such a big problem as long as the left side of the lock is decently positionned.

Now you guys can fix all those old Tanaka Revolvers sleeping in their crates waiting for replacement parts that will never come!
__________________
Jimski is offline   Reply With Quote
Old February 26th, 2009, 10:12   #9
Jimski
 
Jimski's Avatar
 
Join Date: Jun 2005
Location: Montreal
polyurethane glue wasn't strong enough !
apart from that the part did really provide some smooth action for some time.

everything I tried has failed so far, it needs a machined steel component here.
crap!
__________________

Last edited by Jimski; March 2nd, 2009 at 14:08..
Jimski is offline   Reply With Quote
Old March 2nd, 2009, 14:38   #10
Long_Bong
 
Long_Bong's Avatar
 
Join Date: Dec 2007
Location: Canada
Why not try soldering it again? Rather then using glue?
__________________
Long_Bong is offline   Reply With Quote
Old March 2nd, 2009, 14:55   #11
Jimski
 
Jimski's Avatar
 
Join Date: Jun 2005
Location: Montreal
I don't have the proper soldering gear

do you? I'd be interested
__________________
Jimski is offline   Reply With Quote
Old June 13th, 2010, 01:36   #12
CerberusNet
 
CerberusNet's Avatar
 
Join Date: May 2008
Location: Belle River
I'm looking into getting one of these, keep us updated on how things are going. If you're sure soldering will work I have access to a kit.
CerberusNet is offline   Reply With Quote
Old October 10th, 2010, 08:13   #13
cailingling0322
 
Join Date: Oct 2010
This paper presents a normal air-gun array by comparing the performance parameter and theory of several air-gun source.
cailingling0322 is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Discussion > Doctor's Corner > Gas Gun Solutions

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada
http://triggerairsoft.com/shop/

All times are GMT -4. The time now is 13:17.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.