|
|
|
|
|
||||||||
|
|
|||||||||
| Home | Forums | Register | Gallery | FAQ | Calendar |
| Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
 |
|
|
Thread Tools |
November 27th, 2014, 06:34
|
#1 |
|
upgrade blowback housing for KWA kriss vector
I have recently acquired angel custom reinforced speed blowback housing for my kwa kriss vector http://www.evike.com/products/49278/
it didn't come with instructions on how to install it , only a very small flat screw driver was included in the package. how do I install it in my Kriss? |
|
|
|
|
November 27th, 2014, 06:59
|
#2 |
|
Try this couple of videos. https://www.youtube.com/watch?v=wT4X-XT5x0k
|
|
|
|
|
November 30th, 2014, 17:53
|
#3 |
|
I checked the video, it was good, but it didn't show me how to install a blow back housing unit
|
|
|
|
|
|
December 1st, 2014, 22:17
|
#4 |
|
hey guys, I still need instruction on how to install Blow-back housing for my bolt
|
|
|
|
|
|
December 2nd, 2014, 18:44
|
#5 |
|
Squid Porn Superstar, I love the tentacles!
|
Try following the exploded parts diagram in the manual.
|
|
|
|
|
December 2nd, 2014, 18:58
|
#6 |
|
Not Eye Safe, Pretty Boy Maximus on the field take his picture!
|
Fairly certain I recall taking that housing out with no tools.
Gbb assembly drops out, take the cover off the bottom of the assembly and I think the bb assembly just dropped out the bottom and just rotate the housing to get it out. |
|
|
|
|
December 4th, 2014, 03:57
|
#7 |
|
So, according to the manual diagram, I think that I need to remove part 518 (piston spring hanger roll pin) how do I remove it without causing damage to the bolt. I tried to hitting the pin with a hammer and small screwdriver to no avail. How do I remove it and and install it proper?
|
|
|
|
|
|
December 4th, 2014, 11:09
|
#8 |
|
Not Eye Safe, Pretty Boy Maximus on the field take his picture!
|
Looks like a normal roll pin.
You need a punch of the same size, since you'll have to tap it all the way out. Go to Canadian tire and buy one of those single sleeved twist drills of the proper size. Probably .5mm? Snap the twist drill part off (as it can break during punching anyway) and use the shank to punch the pin out. |
|
|
|
|
December 4th, 2014, 18:30
|
#9 |
|
you are saying that I should take a .5MM drill bit. Snap it in half. Use the remaining drill bit to punch the pin out of place.
|
|
|
|
|
|
December 4th, 2014, 18:51
|
#10 |
|
Not Eye Safe, Pretty Boy Maximus on the field take his picture!
|
yes
|
|
|
|
|
December 4th, 2014, 19:02
|
#11 |
|
♥ LOVES helmets! ♥
Don't shoot me more than 10 times or I'll charge you! 
|
If you are willing to come to Bolton on I'll do it for you for free and maintain you're entire gun. I really want to comparing this blowback housing to stock
__________________
Personal experience not to deal with members: ("rue"complete scamer) |
|
|
|
|
December 5th, 2014, 02:23
|
#12 |
|
I snapped a .5mm screw driver and that did the trick. Quattroisking, I live in Langley BC
|
|
|
|
|
 |
|
||||||
| Bookmarks |
|
|
 |
|
