Modify v2/v3 arl

ybrik · March 31st, 2013, 01:22

Had installed one of these today on a g&p m4 since the stock ARL is gouged when I opened it.

The modify ARL looks good as it has that E-clip that locks the ARL spring preventing it from missing once you disassemble the mechbox in half.

This E-clip would make this modify ARL out-of-spec from a regular one. Once you close the mechbox, this ARL is so tight that the spring wouldn't matter. I just removed this E-clip and it was fine. A good test was that flat screw slot on top, it's now moving freely with its spring tension.

This issue I had could only be isolated on my mechbox and not with other brands. But just an FYI if ever those of you will have issues after installing this with the E-clip...

MaciekA · March 31st, 2013, 08:51

I have several of these installed in all sorts of gearboxes and have only run into fitment issues with perhaps one gearbox (I can't remember which brand now). These ARLs are definitely worth the buy even if you're just buying it for the flat head groove.

Mind you, if you have a dremel you can cut a groove into any ARL... though these ARLs are made out of some nice material and don't crack in two as easily as ARLs from G&P / ACM / Lonex (yes... Lonex... Nobody's perfect).

ybrik · March 31st, 2013, 14:19

Are these modify as hard as guarders?

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

March 31st, 2013, 01:22	#1
ybrik Trader rating Join Date: Jun 2007 Location: Ontario, Canada	Modify v2/v3 arl Had installed one of these today on a g&p m4 since the stock ARL is gouged when I opened it. The modify ARL looks good as it has that E-clip that locks the ARL spring preventing it from missing once you disassemble the mechbox in half. This E-clip would make this modify ARL out-of-spec from a regular one. Once you close the mechbox, this ARL is so tight that the spring wouldn't matter. I just removed this E-clip and it was fine. A good test was that flat screw slot on top, it's now moving freely with its spring tension. This issue I had could only be isolated on my mechbox and not with other brands. But just an FYI if ever those of you will have issues after installing this with the E-clip... __________________ 5.56x45mm + m27 = M249(SAW)

March 31st, 2013, 08:51	#2
MaciekA Trader rating Join Date: Jun 2011 Location: Portland, Oregon, USA	I have several of these installed in all sorts of gearboxes and have only run into fitment issues with perhaps one gearbox (I can't remember which brand now). These ARLs are definitely worth the buy even if you're just buying it for the flat head groove. Mind you, if you have a dremel you can cut a groove into any ARL... though these ARLs are made out of some nice material and don't crack in two as easily as ARLs from G&P / ACM / Lonex (yes... Lonex... Nobody's perfect). __________________ "Mah check" Now you know

March 31st, 2013, 14:19	#3
ybrik Trader rating Join Date: Jun 2007 Location: Ontario, Canada	Are these modify as hard as guarders? __________________ 5.56x45mm + m27 = M249(SAW)

Modify v2/v3 arl

Doctor's Corner