|
|
|
|
|
||||||||
|
|
|||||||||
| Home | Forums | Register | Gallery | FAQ | Calendar |
| Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
 |
|
|
Thread Tools |
March 15th, 2006, 15:07
|
#1 |
|
Taking apart a P90TR Guides anyone?
Im looking to take apart my P90 but wanted to know if there were any guides out there to take a part one. Anything would help, thanks
__________________
  
|
|
|
|
March 15th, 2006, 15:23
|
#2 |
|
Use the gun diagrams posted in the Sticky : Gun Diagram/Tech Sheet collection. P90 is under TM/
And this link is pretty helpful also… http://www.combat2000shop.com/combat...ge/p90/p90.htm
__________________
"Sex is one of the 9 reasons for reincarnation, the other 8 are unimportant." Henry Miller Guardian’s airsoft projects @ http://www3.sympatico.ca/aftershock/ |
|
|
|
|
March 15th, 2006, 15:27
|
#3 |
|
Do you mean 'field stripping', or fully taking it apart?
What are you trying to get access to? ** Nevermind, that link will show you everything you need to know. Keep in mind that you can't get the body-halves of the P90 apart without 'cracking' them apart. They're glued AFAIK. |
|
|
|
|
|
March 15th, 2006, 15:41
|
#4 |
|
|
I want to get to the hopup and gear box, I want to make sure the sleeve isn't bunched or twisted in the hopup and upgrades for better fps. Also having alot of fluxs in fps so I want to see whats causing it, and to up the fps
__________________
|
|
|
|
|
March 15th, 2006, 15:45
|
#5 |
|
Pretty easy to take apart a P90 (one of the easiest I've done).
Basically; 1. Take off bb magazine. 2. Push tab on top of receiver (usually covered by mag) and pull front of receiver off. 3. Take off back stock cover. 4. Remove screw(s) holding battery plate on inside of stock. 5. Remove plate. 6. Slowly pull out mechbox. Ta Da! That's it unless you want to take off hop-up mechanism then just turn it to align notches of hop-up with receiver and pull the entire inner barrel setup out. Pull off clip on hopup mechanism and you can then pull out inner barrel along with hop-up rubber.
__________________
|
|
|
|
|
March 15th, 2006, 16:02
|
#6 |
|
|
Great, thanks alot guys Ill be working on this tonight
__________________
|
|
|
|
|
March 15th, 2006, 17:01
|
#7 |
|
Suggestion; find a local expert for the first time.
|
|
|
|
|
March 15th, 2006, 19:24
|
#8 |
|
to get to the hop-up is very easy.
- take out the magazine - push the 'take-down' tab and slide the two recievers apart - gently push the inner barrel towards the front of the gun and turn it 90 degrees (either direction), and then pull it out (the hop up and all) - [at this point it's best to use the guide] - Take out the retaining tab that holds the P90 hop-up adjustment ring in place, then take the ring off, and push the pin out on the hop-up lever. Take all the little bitty parts out, slide the main hop-body off, and there's the barrel with the sleeve on it. (the pictures in that link will help greatly) |
|
|
|
|
 |
|
||||||
| Bookmarks |
|
|
 |
|
