Noveske N4 12.5" Crusader Build

[cellulose]

Noveske N4 12.5" Crusader AEG Custom Build - YouTube




Chrono:

FPS: 379, 383, 382, 384, 384, 380, 382, 383, 382, 383, Avg: 382

Internals:

- Extreme-Fire SW-Evolution MOSFET
- Intellect (G&P) 7.4v 1200mah 20C LiPo Battery x 2
- MadBull 60 Degree Hop-Up Bucking/X Type Spacer
- MadBull Black Python V2 Tightbore 6.03mm, 363mm
- MadBull Ultimate Hop-Up Chamber
- Modify Aluminum Bearing Piston Head
- Modify Cut-Off Lever
- Modify Enhanced Cylinder 300mm - 450mm
- Modify Enhanced Cylinder Head
- Modify Feeding Nozzle
- Modify Gearbox Spring Set
- Modify Nano Torque 7mm Modular Gearset
- Modify Quantum Piston
- Modify Rotary Spring Guide
- Modify S100+ Spring
- Modify Safety Catch
- Modify Selector Plate
- Modify Steel Trigger
- Modify Switch Assembly
- Modify Torus Reinforced 7mm Gearbox
- SystemA Energy Long Motor
- WolfDragon's Over Discharge PCB v4.2

Externals:

- DyTac Micro T-1/American Defense QD Mount
- King Arms Ambidextrous Magazine Catch
- King Arms Bolt Catch
- King Arms Charging Handle Arm
- King Arms Dust Cover Rod and Spring
- King Arms Gas Tube
- King Arms Steel Selector Switch
- MadBull ACE Buffer Tube
- MadBull Ambidextrous Charging Handle
- MadBull Noveske Crusader 12.5" Barrel
- MadBull Noveske Free Float 12.658" Rail
- MadBull Noveske Gas Block
- MadBull Noveske KX3 Flash Hider
- MadBull Noveske MUR Upper Receiver
- MadBull Noveske N4 Lower Receiver
- Magpul PTS 20 70rd PMAG M Series (FG)
- Magpul PTS 30 120rd PMAG (FG) x 4
- Magpul PTS ASAP Ambidextrous Sling Mount
- Magpul PTS Enhanced Buttpad .7"
- Magpul PTS MOE Pistol Grip (FG)
- Magpul PTS MOE Stock (FG)
- Magpul PTS MOE Trigger Guard (FG)
- Magpul PTS RSA Rail Sling Attachment
- Magpul PTS RVG Rail Vertical Grip (FG)
- Magpul Ranger Floorplate (FG) x 5
- Magpul XTM Rail Panels (FG) x 5
- Unknown Dust Cover

Details:

I started this build in April of 2010, it started out as the MadBull Noveske receiver set and I built it up from there. All parts were purchased new from various sources over the past year and a half and assembled by me. I tried to keep the parts as consistent as possible, the majority of parts are MadBull, Modify and Magpul. Externally all the parts that can be are MadBull, I used Magpul PTS accessories for the most part, the receiver accessories are for the most part King Arms.

Internally the entire gearbox is Modify with the modular gearset and the motor is the SystemA Energy. I used Deans 16 gauge wire and installed the Extreme-Fire SW-Evolution MOSFET with WolfDragon PCB v4.2 for LiPo monitoring. The monitoring PCB has been wired for 2 cell LiPo batteries. The MOSFET is currently set at Safe-Semi-Auto and I'm getting 1050 rounds per minute which is about 17 rounds a second at 380FPS.

I built it with a design in mind and tried to find the best parts possible. I wanted an AEG that didn't look like an AEG thus I packed the MOSFET, LiPo monitor and battery into the buffer tube and made it as sleek as possible. It took a while to get it to the stage it's at now as when I started some of the parts were not even in exsistence.

Seeing as the rail is 12.658" and the outer barrel is 12.5" I had to use some orings to get the proper spacing of the flash hider as I wanted it to sit a little bit away from the rail. I also used a oring under the barrel nut to get the perfect top rail clocking.

[cellulose]

Updated parts listing, put up a new picture and added a bit of a description.

[SuperHog]

Sweet gun. You certainly put in the best stuff.

How was the fitting of the Lipo in the buffer tube? Is there room for a 3S 11.1V?

[bizkilter]

B-e-a-utiful!

[cellulose]

Thank you!

In regards to fitting the LiPo, I initially had the MadBull PX04 11.1v 1000mAh 15C in there though the boards would stick out from the end of the tube, also with the MOSFET the continuous discharge rate of 15A was not sufficient so I opted for a 7.4v 1200mAh 20C. With that I can pack everything in the tube and still get fantastic performance, I also prefer putting less voltage through to increase longevity of the internals.

With this MOSFET, LiPo monitor and battery combo I can collapse the stock all the way.

[icaris]

Looks great man.

[bizkilter]

That's an issue I'm had with my current build as well Cell. I opted to replace the magpul stock with a hurricane 614 from JG just for the extra room.