Airsoft Canada
http://triggerairsoft.com/shop/

Go Back   Airsoft Canada > Discussion > Doctor's Corner
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

WE GBBR nozzle failure, bolt stuck back.

:

Doctor's Corner

Reply
 
Thread Tools
Old June 27th, 2014, 19:58   #1
TANNER
ChrisUK
 
TANNER's Avatar
 
Join Date: Aug 2008
Location: Toronto
WE GBBR nozzle failure, bolt stuck back.

WE GBBR M4

Nozzle spring seems to have failed and is now stuck in back of bolt. This causes the bolt to not be able to return full fore-ward which means 1/10th of it is stuck in the buffer tube meaning the receiver cannot be broken in half to remove the bolt.

Thoughts?

Puzzling problem.
__________________
TANNER is offline   Reply With Quote
Old June 27th, 2014, 20:56   #2
Aper
E-30
 
Aper's Avatar
 
Join Date: Jan 2004
Location: Aegiis's Neighbor.
Open or closed bolt ?

Did you change your stock recently ? If so, did you put in the rubber shim inside the buffer tube originaly ?
__________________

West Coast EOD Supporter. // Bang One, Bang Em All ! // In war, it's not who's right, but who's left.

Last edited by Aper; June 27th, 2014 at 20:59..
Aper is offline   Reply With Quote
Old June 27th, 2014, 21:02   #3
Drake
E-01
 
Drake's Avatar
 
Join Date: Dec 2001
Location: Montreal, QC
1) if the bolt just isn't closing completely you can use the forward assist to try and move it forward manually;

2) otherwise just loosen the castle nut and unscrew the buffer tube, you'll be able to pull the bolt carrier assembly out the back of the receiver.
__________________
Drake is offline   Reply With Quote
Old June 27th, 2014, 22:16   #4
N_Force
 
N_Force's Avatar
 
Join Date: Oct 2006
Location: Toronto, Ontario
There is a little pin and spring at the front end underneath the buffer tube to stop the buffer. That pin could be off position a bit and making the bolt got struck.
__________________
aka Uncle

N_Force is offline   Reply With Quote
Old June 27th, 2014, 23:41   #5
TANNER
ChrisUK
 
TANNER's Avatar
 
Join Date: Aug 2008
Location: Toronto
Thanks for the input guys, appreciate your help.

Here is some more info.

- Open bolt.

- Stock was not changed, all stock except for hop rubber and npas.

- Forward assist is unable to push bolt forward, nozzle will not return all the way back into the bolt stopping the bolt from moving forward all the way (causing the protrusion)

- Had the buffer tube off and tried to remove the bolt through the rear. while I can get the bolt to move back and fourth its not possible to pull all the way though the rear due to the roll pin part of the bolt. (See picture)

- Pin underneath the bolt is working fine, not stopping the bolt in any way.

I have also tried pulling the bolt as far out as I can (to the slim part) and then separate the receiver hoping the extra space would give me some wiggle room. Did not work.

__________________
TANNER is offline   Reply With Quote
Old June 28th, 2014, 00:17   #6
Drake
E-01
 
Drake's Avatar
 
Join Date: Dec 2001
Location: Montreal, QC
With the stock tube off and no tension on the bolt carrier, you should be able to pop out the front and rear receiver pins and pull the upper off (carefully)
__________________
Drake is offline   Reply With Quote
Old June 28th, 2014, 01:54   #7
PaddMadd
uMadd, Padd?
 
PaddMadd's Avatar
 
Join Date: Feb 2009
Location: Vancouver Island, BC
Send a message via MSN to PaddMadd
My guess is that the little pin holding the two pieces of your nozzle together has come out and possibly bent, which is forcing it into place in mid-travel. The only way you'll get that bolt out of the receiver is to force the bolt into battery\. Doing this can damage your stock bolt, but it's the only way to stop your GBBR from becoming a very big paperweight.
__________________
Quote:
Originally Posted by pusangani View Post
Did he not pay his ASC bill this month?

Last edited by PaddMadd; June 28th, 2014 at 01:57..
PaddMadd is offline   Reply With Quote
Old June 28th, 2014, 04:20   #8
GBBR
Banned
 
Join Date: Sep 2012
Location: Toronto
Send a message via MSN to GBBR Send a message via Skype™ to GBBR
take off the front end, that way the bolt can sit fully forward and then you can do a full takedown of the gun, PM me if you need futher help, it is the ONLY way to safely disassemble the gun.
GBBR is offline   Reply With Quote
Old June 28th, 2014, 10:30   #9
TANNER
ChrisUK
 
TANNER's Avatar
 
Join Date: Aug 2008
Location: Toronto
Took of the front end which allowed the bolt forward enough to split the receivers, freeing the bolt from its prison. Thanks guys!

Here was the root of the problem:

Spring snapped and coiled up at the back of the bolt causing the backup, pin slightly bent. Everything else looks ok. Is this a common problem?

__________________
TANNER is offline   Reply With Quote
Old June 28th, 2014, 10:34   #10
TANNER
ChrisUK
 
TANNER's Avatar
 
Join Date: Aug 2008
Location: Toronto
Seems like an elusive part to replace. Anyone know where to pick these parts up?
__________________
TANNER is offline   Reply With Quote
Old June 28th, 2014, 10:43   #11
N_Force
 
N_Force's Avatar
 
Join Date: Oct 2006
Location: Toronto, Ontario
Is it copper? Replacing the steel spring and pin? First time I saw it for internal parts!
__________________
aka Uncle

N_Force is offline   Reply With Quote
Old June 28th, 2014, 10:47   #12
TANNER
ChrisUK
 
TANNER's Avatar
 
Join Date: Aug 2008
Location: Toronto
Look like I can get both parts buy buying another full stock nozzle.

http://www.airsoftparts.ca/store2/in...oducts_id=2273
__________________
TANNER is offline   Reply With Quote
Old June 28th, 2014, 10:51   #13
Hectic
Oh we do hate you, just never felt like wasting the time to give you a user title :P
 
Hectic's Avatar
 
Join Date: Apr 2007
Location: Toronto, Ontario
this happened to me too (on my 416) only failiure so far after 2 seasons. I had to remove the buffer to get it out as well. it was a pain lol. Also bought the whole nozzle set for the replacement spring lol
__________________
Quote:
Originally Posted by m102404 View Post
Hectic....FFS start writing in coherent sentences!!!
Quote:
Originally Posted by JDoorn View Post
Thanks Hectic,
While your posts are sometimes a difficult read, you sure are helpfull
Lvl. 3 certified sniper
FinchFieldAirsoft
Hectic is offline   Reply With Quote
Old June 28th, 2014, 15:53   #14
siggypoo
 
siggypoo's Avatar
 
Join Date: Mar 2009
Location: Oshawa, Ontario.
WE GBBR nozzle failure, bolt stuck back.

I can't see via Tapatalk if you're AV'd, but if so, I'd suggest browsing the parts classifieds here for what you want. Hasn't failed me yet.
__________________
siggypoo is offline   Reply With Quote
Old June 28th, 2014, 19:29   #15
Red62
 
Red62's Avatar
 
Join Date: Jul 2008
Location: Richmond Hill

Well, have fun finding a new spring and replacing it- you gotta take out the c clip at the back of the bolt to get the parts out. Be careful when taking out the spring pin- they're often one-way.
__________________
Quote:
Originally Posted by Thenooblord View Post
good ol red62, I shot him more than all of Eco I bet, LOL
**Certified Tornado Tech**Will fix your guns for food and BBs**
Red62 is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Discussion > Doctor's Corner

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada
http://triggerairsoft.com/shop/

All times are GMT -4. The time now is 20:48.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.