Looking to make the most powerful KSC G26, HELP.....

[Amos]

Originally Posted by MikeMcNair

Ok, AS spring out, AS valve in with stock spring....

EUREKA!!!!!!

Gun fires hard and fast, is seemingly consistant, and is destroying my test shot bag (bag full of empty beer cans)

This was the isssue! So, no more airsoft surgeon spring in the floating valve assembly, it sucks a fat one.

Now, waiting on the other parts to make her more powerful. Then, back to the army navy store to chrono again.

Wait until those .3 Bastards arrive... That gun's gonna be firing NICE and far.

[MikeMcNair]

looking forward to it. they will compliment the other goodies coming.

i am telling ya, i will get some sick power outa this thing if it kills me.

[MikeMcNair]

GD-PT-GLOCK07 Guarder Enhanced Piston Lid for
GD-PT-GLOCK10 Guarder Enhanced Hammer Spring
GD-PT-GLOCK12 Guarder Magazine Catch
Shooters Design Reinforced Part 10 for KSC Glock
SD-PT-S718 Shooters Design Steel Impact Hammer
New High Flow Mag Valve
new part # 23 (one of the springs is bent)
Guarder Enhanced part # 207 for Magazine

this, .30g pellets, and red gas should get me where i want to be

[Tex]

good to hear that valve is working now. again I will point out that part 10 needs to be part 8. hope you have not ordered it yet or can exchange it.

[MikeMcNair]

thanks tex, you are right, and they are sending me the part #8, i just cut and pasted from the original order.

thanks again!!!

it is 90 degrees out today, REALLY warm gun is breaking bottles in said bag o' stuff i am testing in.

[MikeMcNair]

someone wanted to see how i did the teflon tpe on the hop up/inner barrel, well this is what i came up with...........




hope that helps a bit

[Donster]

i thought you were supposed to tape the part where the inner barrels meets the rest of the assembly? perhaps i was wrong though

[MikeMcNair]

i will try that too. i was kinda flying blind, and looked for possible leaks.

your description makes some good sense tho

[Semi Pro]

Originally Posted by MikeMcNair

someone wanted to see how i did the teflon tpe on the hop up/inner barrel, well this is what i came up with...........




hope that helps a bit

thankyou:tup:

[MikeMcNair]

ok, here is current setup................

[MikeMcNair]

current list of gooodies...............

UN Custom-KSC G26 Metal Version
- KSC G26 Based
- KSC G26 Metal Slide Installed
- Hi-Flow Valve Installed
- Strengthen Recoil Spring Installed
- Tuned For Top Gas
- Airsoft Surgeon Power-Up Floating Valve(using stock spring)
- PDI 6.01 Precision Inner Barrel
- GD-PT-GLOCK07 Guarder Enhanced Piston Lid
- GD-PT-GLOCK10 Guarder Enhanced Hammer Spring
- GD-PT-GLOCK12 Guarder Magazine Catch
- Shooters Design Reinforced Part 8 for KSC Glock
- SD-PT-S718 Shooters Design Steel Impact Hammer
- Proud-Mag-04
- Proud-Spring-13
- KA-08-01 Hgh utput Valve
- KSC G19/G23F Part No.23
- green gas
- teflon mod on barrel and bumper
- .23g's(soon to have .30 Bastard BB's)

more to follow.............

[MikeMcNair]

if anyone has any other suggestions, please let me know, as i am all ears.

[Amos]

Don't think you did the Teflon tape mod properly...

From my understanding of it, you're supposed to teflon tape the hop-up to the barrel to stop any leaks..

But I don't bother with mods like that with such a limited life-span

[MikeMcNair]

werd, it is tough to see, but i have the tape around the barrel enough to allow the bumper to VERY TIGHTLY slide over it. so i think the seal is pretty dam tight there.

if you look at the last pic closely, you can see it coming out JUST past the metal part.

if you look in the pic, you can see where the overhang of rtape is on the barrel, making the rubber bumper thing fit SUPER snug right there. then, once i put the hop up ball and metal adjuster on it, it is SUPER tight, so i am pretty sure it is air tight now

[MikeMcNair]

EDITED POST SINCE uncompany MADE ME WHOLE, AND DID SO IN A TIMELY MANNER. THANK YOU UNCOMPANY.COM!!!