FAS - TECHNICAL REFERENCE For Upgrading & Modifications

[Kampfer]

Update and add

Mechbox Version7 for TM M14
Standard gear set for all other AEGs.
Special Spur gear for M14 and Famas (smaller)
Special cylinder longer than others. M14's cylinder is 73.33mm long

TM mechbox uses 6mm bushing
G&P mechbox uses 7mm ball bearing
CA new mechbox uses 7mm ball bearing

G&G, Prometheus reinforced piston do not work with Hurricane reinforced version2 mechbox, TM stock version7 and Version 1 (Famas) mechbox.

New CA version 2 mechbox have implemented the crack prevention mod (rounding the corners) but they still use dried up Li grease.

Half teeth pistons are for Super High torque gears because the selector gear is larger in diameter.

[dcon27]

CA SLR 105 barrel = 463mm

[crosby87]

God this thread is old. I was reading it and just had a question. Just wondering if anyone knew what Internal Resistance means in a battery. Examples...

[ILLusion]

It's the inefficiency in a cell that prevents the energy being converted from a chemical state to an electrical state without a loss in performance.

Generally, high internal resistances will be outputted as heat (ie, wasted energy).

Does that answer your question?

[Spa]

What about CA pistons?

[crosby87]

Originally Posted by ILLusion

It's the inefficiency in a cell that prevents the energy being converted from a chemical state to an electrical state without a loss in performance.

Generally, high internal resistances will be outputted as heat (ie, wasted energy).

Does that answer your question?

Thats helpful. So it is how efficent a cell is I presume. But as a result, would a lower Ohm rating mean more rof? (see last page)

[ILLusion]

Originally Posted by Spa

What about CA pistons?

What about them?

Originally Posted by crosby87

Thats helpful. So it is how efficent a cell is I presume. But as a result, would a lower Ohm rating mean more rof? (see last page)

As Ohm's law states, the lower the resistance, the higher the allowed current draw (assuming voltage stays the same). If more current is allowed to be drawn, then the motor will get better use of what's available, and as a result, greater torque and ROF are available.

So yes, assuming V and I are the same, then lower R will give higher ROF.

[Spa]

Are CA pistons that bad that they were not included on your list?

[ILLusion]

Originally Posted by Spa

Are CA pistons that bad that they were not included on your list?

I only have experience with first generation CA pistons... and yes, they really WERE that bad.

Although I'm sure CA has made leaps and bounds since their first releases years ago... I just have not had a chance to handle them yet.

[tukbuk21]

does anyone know if the ics quick detachment silencer (short version) would work with the echo 1 g36c

[khojie]

hi to all im khojie a gunsmith i can make your guns what you want like sp120 is 430-440 sp130 -520 sp140 540-sp150 570 sp170 640 sp180 720-750 in any aeg -ak only tnx

[khojie]

hi to all im khojie a gunsmith i can make your guns what you want like sp120 is 430-440 sp130 -520 sp140 540-sp150 570 sp170 640 sp180 720-750 in any aeg -ak only tnx

[Bowers]

where are you located?

[Yannos]

hmmmm. why didn't you post a new thread if its important? And yeah .. were are you located ?

[Gunk]

Originally Posted by khojie

hi to all im khojie a gunsmith i can make your guns what you want like sp120 is 430-440 sp130 -520 sp140 540-sp150 570 sp170 640 sp180 720-750 in any aeg -ak only tnx

Any AEG, but AK only?

And I'm confused... are you telling us what FPS rating an AEG will have with certain springs?

I'm not a gun tech, and I coulda figured that out... I smell a bridge lurker.