Airsoft Canada
www.jsairsoft.com

Go Back   Airsoft Canada > Information Center > Newbie Tank
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

Well Mb03 or TSD R700

:

Newbie Tank

Reply
 
Thread Tools Search this Thread
Old October 13th, 2009, 18:56   #1
Vanchen
 
Join Date: Jun 2009
Location: Toronto
Well Mb03 or TSD R700

I wanted to fill the stock with home renovation insulating foam but I'm not sure where to apply. The back buttplate doesn't have any screws and I'm afraid to pull it off. Does anybody know if you can pry it off or apply the foam in the little whole in the front?
Vanchen is offline   Reply With Quote
Old October 13th, 2009, 19:15   #2
Outcast569
 
Outcast569's Avatar
 
Join Date: Oct 2007
Location: Calgary, Alberta
Send a message via MSN to Outcast569
If its the same as the VSR and it should be it just comes off. Just pull. Its just a rubber plate with lips on it that fit in a groove.

As far as putting foam in it. Ive never had an issue with rattle or weight for the time Ive had mine.

Just my 0.02
__________________
Outcast569 is offline   Reply With Quote
Old October 13th, 2009, 19:25   #3
aznpos531
 
aznpos531's Avatar
 
Join Date: Jan 2009
Location: Toronto
You're looking for this: linky
__________________

Quote:
Originally Posted by OptimusPrime View Post
I could never stop going to WalMart. Its the only place I can get good airsoft guns.
aznpos531 is offline   Reply With Quote
Old October 13th, 2009, 19:42   #4
Vanchen
 
Join Date: Jun 2009
Location: Toronto
The butt plate on the stock is damn hard to get off. Any suggestions?
Vanchen is offline   Reply With Quote
Old October 13th, 2009, 19:48   #5
aznpos531
 
aznpos531's Avatar
 
Join Date: Jan 2009
Location: Toronto
You can try wedging a Philips screwdriver between the stock and the butt plate (careful not to damage the plastic/rubber of either part) to loosen it and the rest is all about elbow grease.
__________________

Quote:
Originally Posted by OptimusPrime View Post
I could never stop going to WalMart. Its the only place I can get good airsoft guns.
aznpos531 is offline   Reply With Quote
Old October 13th, 2009, 20:02   #6
Vanchen
 
Join Date: Jun 2009
Location: Toronto
Well, I pried off the back and in the stock is a big weight? with masking tape on it that doesn't want to come out. More help plz. So much helping.
Vanchen is offline   Reply With Quote
Old October 13th, 2009, 21:03   #7
aznpos531
 
aznpos531's Avatar
 
Join Date: Jan 2009
Location: Toronto
Unless you're unhappy with the balance and/or weight of the rifle, I'd leave it where it is. If you foam the stock without the weight in it, your rifle will be a lot lighter and probably off balance. If you want it to be a little heavier, you can add more weights, but make sure you're happy with the final weight and balance before you foam. The rest should be very clearly outlined in the guide I linked you to a few posts back.
__________________

Quote:
Originally Posted by OptimusPrime View Post
I could never stop going to WalMart. Its the only place I can get good airsoft guns.
aznpos531 is offline   Reply With Quote
Old October 14th, 2009, 18:15   #8
Vanchen
 
Join Date: Jun 2009
Location: Toronto
The giant weight blocks the whole stock so I can't foam it b/c theres only a 1cm gap between the weight and the sides.
Vanchen is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Information Center > Newbie Tank

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada
www.jsairsoft.com

All times are GMT -4. The time now is 22:25.


Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2017, vBulletin Solutions, Inc.