Airsoft Canada
Airsoft Depot

Go Back   Airsoft Canada > Information Center > Newbie Tank
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

Spray Paint - refit issue

:

Newbie Tank

Reply
 
Thread Tools Search this Thread
Old January 7th, 2013, 23:01   #1
MatthewRyan
 
MatthewRyan's Avatar
 
Join Date: Dec 2012
Location: Toronto
Spray Paint - refit issue

Hello all ...

I have my TM px4 and obviously has a tinted receiver I keep getting mixed answers should i remove ALL internals and spray paint inside or just spray the outside .. ive been told krylon camo ultra flat is the best paint ..

I know to cover everything that i dont want sprayed
Do you think there may be a refitting issue

thoughts, comments, suggestions

thank you
MatthewRyan is offline   Reply With Quote
Old January 8th, 2013, 00:07   #2
Cpt- Lovegrove
 
Cpt- Lovegrove's Avatar
 
Join Date: Oct 2011
Location: kingston ontario canada
as long as you keep it thin , it should be fine,
Cpt- Lovegrove is offline   Reply With Quote
Old January 8th, 2013, 00:20   #3
Hectic
Oh we do hate you, just never felt like wasting the time to give you a user title :P
 
Hectic's Avatar
 
Join Date: Apr 2007
Location: Toronto, Ontario
just strip downt the postol remove all the mooving bits tape off the openings and contact points of the slide and paint i right to wave from having to sand stuff to get it workin afterwords, its easyer to just tape it
__________________
Quote:
Originally Posted by m102404 View Post
Hectic....FFS start writing in coherent sentences!!!
Quote:
Originally Posted by JDoorn View Post
Thanks Hectic,
While your posts are sometimes a difficult read, you sure are helpfull
Lvl. 3 certified sniper
FinchFieldAirsoft
Hectic is offline   Reply With Quote
Old January 8th, 2013, 07:24   #4
redneck12
 
Join Date: Mar 2011
Location: Oshawa
When I painted my G17 lower I removed all the internals and sprayed a light coat inside then 2 or 3 coats on the outside then 2 coats of clear on the outside and a coat of clear on the inside. I did not have any problems refitting the internals just remember to keep your coats thin and even.
__________________
WE M4-- C8 CQBR
WE M4 13" Troy TRX build
WE M-16 DMR
redneck12 is offline   Reply With Quote
Old January 8th, 2013, 09:05   #5
nstahl.19
 
nstahl.19's Avatar
 
Join Date: Oct 2012
Location: Kitchener, ON
Just lightly dust it until everything is covered. You'll get an idea how far away to stay with the can when you start painting. And keep it equal. Also what do you mean by refitting? Will you be taking the gun apart and then painting it? Just tape off everything that shouldn't be painted and should be good to go.
nstahl.19 is offline   Reply With Quote
Old January 8th, 2013, 13:12   #6
Armyissue
Administrator of Pants
 
Armyissue's Avatar
 
Join Date: Sep 2004
Location: Port Credit
Send a message via MSN to Armyissue Send a message via Skype™ to Armyissue
light (220) sanding then spray coating, then your Moms fishnet stockings. Not the heels, just the fishnet stockings.
Armyissue is offline   Reply With Quote
Old January 8th, 2013, 14:44   #7
13enz
 
13enz's Avatar
 
Join Date: May 2011
Location: Mississauga, Ontario.
As mentioned above. Don't cake it on, otherwise things wont cycle properly. Obtained an old 1911, the lower was layered with paint. The slide wouldn't even budge.
13enz is offline   Reply With Quote
Old January 13th, 2013, 23:56   #8
MatthewRyan
 
MatthewRyan's Avatar
 
Join Date: Dec 2012
Location: Toronto
yea i finally picked up my can of krylon camo ultra flat black .. im not the artsy type so im a little nervous might ask someone on the block who's done their fare share of spray painting .. i make stick people look bad < my artistic talent .. but yea I might just tape all the internals remove the magazine catch and spray
MatthewRyan is offline   Reply With Quote
Old January 14th, 2013, 00:36   #9
Hectic
Oh we do hate you, just never felt like wasting the time to give you a user title :P
 
Hectic's Avatar
 
Join Date: Apr 2007
Location: Toronto, Ontario
put down some card board or news paper and shake the can well and hold it far back like 1-2 ft and spray as u pass over the gun back n forth pilut a thin coat let it dry 10-15 min and reapply till its painted evenly, read the can itll tell u wht to do, and yes tape internals off like i said befor. Ie the magwell slide rails, the hole left from removing mag release the hammer area.
__________________
Quote:
Originally Posted by m102404 View Post
Hectic....FFS start writing in coherent sentences!!!
Quote:
Originally Posted by JDoorn View Post
Thanks Hectic,
While your posts are sometimes a difficult read, you sure are helpfull
Lvl. 3 certified sniper
FinchFieldAirsoft
Hectic is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Information Center > Newbie Tank

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada
Airsoft Depot

All times are GMT -4. The time now is 03:43.


Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2017, vBulletin Solutions, Inc.